Keyless Go + control module with Bluetooth®
Unique on the market, the module offers the possibility to control a complete vehicle with a small wiring harness.
The entire setup and the alarm system can be controlled via the m.ride app. A fault diagnosis is possible during operation and without removing the m.unit. You can also use a secure, encrypted keyless-go feature.
When activated, approaching with your own smartphone is sufficient to get the vehicle ready for take-off. Thus, the on-board voltage can be switched on by pressing the start button. A further pressure then starts the engine. Once switched on, the electrical system remains safely activated while driving, even without a telephone.
The module is the digital control unit for a vehicle, the heart of the entire vehicle electrical system. It can be operated with push-button fittings or with conventional, switching handlebar fittings. It switches all necessary components on the vehicle and at the same time it assumes the tasks of the electrical fuses.
Relays and individual components in the wiring harness are greatly reduced and a new, minimized wiring of the vehicle can be made in no time.
When using the module, the number of all switch fitting connections is reduced to a single cable.
Functions via Bluetooth or App
Encrypted connection via Bluetooth® LE (Low Energy), thus tamper-proof
Extremely low power consumption of smartphone and m.unit blue (with active Bluetooth 0.9mA and in Powersave mode after 6 weeks of inactivity: 0.3mA)
Keyless-Go (start of the vehicle by approaching with your own smartphone)
Highly sensitive accelerometer allows you to visualize your driving activity in m.ride through an activity factor, number of turns, top speed, etc.
Transmission of alarm events (with date, time, vehicle on the ground, etc.) to the app
Setting the mode and sensitivity of the alarm system
Monitoring the current battery voltage in the app
Diagnosis of all inputs and outputs, measurement of currents, voltage, device temperature
Defect detection of all lamps by calibration. Due to faulty turn signals doubling of the flashing frequency, status message in the app and audio hint by Rideassist.
Rideassist: optional turn signal sound and error messages in real time as an audio output via helmet headset.
Manual switching of outputs via smartphone (except starter)
Firmware updates without removal at any place via smartphone and app
Configuration of the setup menu without expansion at any place via smartphone and app
Vehicle management with automatic instructions for maintenance tasks, condition of tires, chain, brake pads, oils, consumables, spark plugs, etc. by adjusting the vehicle mileage level by means of tacho signal
Log records trips and saves all generated vehicle messages, alarm events, and maintenance tasks
Display of parking position and ping! to help with vehicle search
LIN bus connection available for later connection of suitable motogadget products
Functions without mobile or APP
Complete digital button control, 4-button or 5-button operation possible
Complete replacement for the fuse box. 10 independent circuits are digitally monitored and switched off in the event of faults. After the fault has been eliminated, the backup function is automatically reset
Integrated, position-independent alarm system
Integrated, digital, load-independent flasher relay, automatic switch-off optional and adjustable, m.wave mode selectable
Integrated hazard warning lights
Turn signal optional as position light adjustable
Parking light and flashlight integrated
Control of dipped and high beam (up to 200 W switching power) with just one button
Integrated, digital brake light modulator, flashing mode programmable
Acceleration-controlled hazard brake light (automatic warning signal)
Integrated starter relay for starters with magnetic switch (up to 30 A switching capacity)
Intelligent and configurable control / shutdown of the consumers, in order to be able to use the maximum starting energy of the battery during the starting process
Integrated digital horn relay
Two configurable auxiliary outputs AUX1 and AUX2
Diagnostic function for assignment of input, output, switching status of the circuit, short-circuit diagnosis, etc.
Calibration and current measurement enables defect detection of all bulbs
Technical specifications
L / W / H 90 x 53 x 30 mm, bore distance 74 mm
Weight approx. 180 g
Mounting 2 x M5 stainless steel screws (mounting and ground connection), 1 x M5 screw contact for battery plus
Operating voltage 6 V - 20 V.
Operating temperature -20 ° ... + 80 ° C
Inputs 1 x input (+ 12V switched) for ignition lock or m.lock
11 x control input (minus / ground switched) for:
left blinker
right blinker
Low / high beams
starter
horn
stoplight
Kill switch
stand switch
LIN bus
AUX1
AUX2
Outputs 10 x output (+ 12V) for:
left blinker
right blinker
dimmed headlights
high beam
begin
The entire setup and the alarm system can be controlled via the m.ride app. A fault diagnosis is possible during operation and without removing the m.unit. You can also use a secure, encrypted keyless-go feature.
When activated, approaching with your own smartphone is sufficient to get the vehicle ready for take-off. Thus, the on-board voltage can be switched on by pressing the start button. A further pressure then starts the engine. Once switched on, the electrical system remains safely activated while driving, even without a telephone.
The module is the digital control unit for a vehicle, the heart of the entire vehicle electrical system. It can be operated with push-button fittings or with conventional, switching handlebar fittings. It switches all necessary components on the vehicle and at the same time it assumes the tasks of the electrical fuses.
Relays and individual components in the wiring harness are greatly reduced and a new, minimized wiring of the vehicle can be made in no time.
When using the module, the number of all switch fitting connections is reduced to a single cable.
Functions via Bluetooth or App
Encrypted connection via Bluetooth® LE (Low Energy), thus tamper-proof
Extremely low power consumption of smartphone and m.unit blue (with active Bluetooth 0.9mA and in Powersave mode after 6 weeks of inactivity: 0.3mA)
Keyless-Go (start of the vehicle by approaching with your own smartphone)
Highly sensitive accelerometer allows you to visualize your driving activity in m.ride through an activity factor, number of turns, top speed, etc.
Transmission of alarm events (with date, time, vehicle on the ground, etc.) to the app
Setting the mode and sensitivity of the alarm system
Monitoring the current battery voltage in the app
Diagnosis of all inputs and outputs, measurement of currents, voltage, device temperature
Defect detection of all lamps by calibration. Due to faulty turn signals doubling of the flashing frequency, status message in the app and audio hint by Rideassist.
Rideassist: optional turn signal sound and error messages in real time as an audio output via helmet headset.
Manual switching of outputs via smartphone (except starter)
Firmware updates without removal at any place via smartphone and app
Configuration of the setup menu without expansion at any place via smartphone and app
Vehicle management with automatic instructions for maintenance tasks, condition of tires, chain, brake pads, oils, consumables, spark plugs, etc. by adjusting the vehicle mileage level by means of tacho signal
Log records trips and saves all generated vehicle messages, alarm events, and maintenance tasks
Display of parking position and ping! to help with vehicle search
LIN bus connection available for later connection of suitable motogadget products
Functions without mobile or APP
Complete digital button control, 4-button or 5-button operation possible
Complete replacement for the fuse box. 10 independent circuits are digitally monitored and switched off in the event of faults. After the fault has been eliminated, the backup function is automatically reset
Integrated, position-independent alarm system
Integrated, digital, load-independent flasher relay, automatic switch-off optional and adjustable, m.wave mode selectable
Integrated hazard warning lights
Turn signal optional as position light adjustable
Parking light and flashlight integrated
Control of dipped and high beam (up to 200 W switching power) with just one button
Integrated, digital brake light modulator, flashing mode programmable
Acceleration-controlled hazard brake light (automatic warning signal)
Integrated starter relay for starters with magnetic switch (up to 30 A switching capacity)
Intelligent and configurable control / shutdown of the consumers, in order to be able to use the maximum starting energy of the battery during the starting process
Integrated digital horn relay
Two configurable auxiliary outputs AUX1 and AUX2
Diagnostic function for assignment of input, output, switching status of the circuit, short-circuit diagnosis, etc.
Calibration and current measurement enables defect detection of all bulbs
Technical specifications
L / W / H 90 x 53 x 30 mm, bore distance 74 mm
Weight approx. 180 g
Mounting 2 x M5 stainless steel screws (mounting and ground connection), 1 x M5 screw contact for battery plus
Operating voltage 6 V - 20 V.
Operating temperature -20 ° ... + 80 ° C
Inputs 1 x input (+ 12V switched) for ignition lock or m.lock
11 x control input (minus / ground switched) for:
left blinker
right blinker
Low / high beams
starter
horn
stoplight
Kill switch
stand switch
LIN bus
AUX1
AUX2
Outputs 10 x output (+ 12V) for:
left blinker
right blinker
dimmed headlights
high beam
begin
Unfortunately there are no review yet. Be the first who rate this product.