Crash protectors

Crash protectors

Crash protectors on motorcycle frame

 

Type PH01-K

Classic crash protectors in the "mushroom" design are made from black polyamide. Protectors are 50mm wide and 60mm long. Each protector contains an internal steel insert to increase its strength and therefore it allows the use of shorter screws during the assembly. Protectors are tested on the road and on the racetrack. Each protector passes through quality and manufacturing control.
picture


 

Type PH01-W

Classic crash protectors in the "mushroom" design are made from white polyamide. Protectors are 50mm wide and 60mm long. Each protector contains an internal steel insert to increase its strength and therefore it allows the use of shorter screws during the assembly. Protectors are tested on the road and on the racetrack. Each protector passes through quality and manufacturing control.
picture


 

Type PHV1K

Classic crash protectors with the anodized cap are made from black polyamide. Caps are available in seven colours. Protectors are 50mm wide and 60mm long. Each protector contains an internal steel insert to increase its strength and therefore it allows the use of shorter screws during the assembly. Protectors are tested on the road and on the racetrack. Each protector passes through quality and manufacturing control.
picture


 

Type PHV1W

Classic crash protectors with the anodized cap are made from white polyamide. The caps are available in seven colours. Protectors are 50mm wide and 60mm long. Each protector contains an internal steel insert to increase its strength and therefore it allows the use of shorter screws during the assembly. Protectors are tested on the road and on the racetrack. Each protector passes through quality and manufacturing control.
picture


 

Type PHV2K

Classic crash protectors with the anodized cap are made from black polyamide. Caps are available in seven colours. Protectors are 50mm wide and 60mm long. Each protector contains an internal steel insert to increase its strength and therefore it allows the use of shorter screws during the assembly. Protectors are tested on the road and on the racetrack. Each protector passes through quality and manufacturing control.
picture


 

Type PHV2W

Classic crash protectors with the anodized cap are made from white polyamide. The caps are available in seven colours. Protectors are 50mm wide and 60mm long. Each protector contains an internal steel insert to increase its strength and therefore it allows the use of shorter screws during the assembly. Protectors are tested on the road and on the racetrack. Each protector passes through quality and manufacturing control.
picture


 

Mounting kits for crash protectors

Mounting kits for crash protectors type PH, PHV1 and PHV2 have the same design, so it is for example possible to replace the protector PH for the protector PHV1. While developing mounting kits for these protectors our goal is to avoid modifying any original parts when you install them on your motorcycle. Nevertheless in some cases there is no other option and it is for example necessary to adjust the plastic part of motorcycle. If there is a possibility to manufacture a mounting kit which will be attached to multiple points, we will do so because this eliminates a possible damage in the mounting spot during a crash. Mounting kits are made of aluminium alloy and then anodized in black, the adapters are milled on CNC machines.
picture


Crash protectors into front and rear wheel axis

 

Type PVN

Crash protectors in the classic design for the front axle of the wheel are made from black polyamide. They mainly serve for the protection of the front fork. The length of the protector is 40mm and its width is 50mm. We recommend to use them together with the protectors for the motorcycle frame. Each protector passes through quality and manufacturing control and it is tested on the road.
picture


 

Type PKN

Crash protectors in the classic design for the rear axle of the wheel are made from black polyamide. They mainly serve for to the protection of the swingarm. The length of the protector is 40mm and its width is 50mm. We recommend to use them together with the protectors for the motorcycle frame. Each protector passes through quality and manufacturing control and it is tested on the road.
picture


 

Type PV1

Crash protectors in the classic design for the front axle of the wheel with anodized aluminium cap. They are made from black polyamide. The caps are available in seven colours They mainly serve for the protection of the front fork. The length of the protector is 25mm and its width is 49mm. Dural reductions for the axis are included. We recommend to use them together with the protectors for the motorcycle frame. Each protector passes through quality and manufacturing control and it is tested on the road.
picture


 

Type PV2

Crash protectors in the classic design for the front axle of the wheel with anodized aluminium cap. They are made from black polyamide. The caps are available in seven colours They mainly serve for the protection of the front fork. The length of the protector is 25mm and its width is 49mm. Dural reductions for the axis are included. We recommend to use them together with the protectors for the motorcycle frame. Each protector passes through quality and manufacturing control and it is tested on the road.
picture


 

Type PK1

Crash protectors in the classic design for the rear axle of the wheel, with anodized aluminium cap. They are made from black polyamide. The caps are available in seven colours. They mainly serve for the protection of the rear fork. The length of the protector is 25mm and its width is 49mm. Dural reductions for the axis are included. We recommend to use them together with the protectors for the motorcycle frame. Each protector passes through quality and manufacturing control and it is tested on the road.
picture


 

Type PK2

Crash protectors in the classic design for the rear axle of the wheel, with anodized aluminium cap. They are made from black polyamide. The caps are available in seven colours. They mainly serve for the protection of the rear fork. The length of the protector is 25mm and its width is 49mm. Dural reductions for the axis are included. We recommend to use them together with the protectors for the motorcycle frame. Each protector passes through quality and manufacturing control and it is tested on the road.
picture


Crash sliders

Crash slider SL01

 

Type SL01K

One of the most effective protections for your motorcycle thanks to the large sliding surface (in comparison with the classical protector). It is made from black polyamide. The length of the slider is 119mm and its height is 72mm. The angle of the protector is adjustable according to the shape of your motorcycle. The caps are anodized and available in seven colours.
picture


 

Type SL01W

One of the most effective protections for your motorcycle thanks to the large sliding surface (in comparison with the classical protector). It is made from the white polyamide. The length of the slider is 119mm and its height is 72mm. The angle of the protector is adjustable according to the shape of your motorcycle. The caps are anodized and available in seven colours.
picture


 

Caps

The caps are made from aluminium and are available in seven colours.
picture


 

Mounting kits for sliders SL01

Mounting kits for crash protectors type PH, PHV1 and PHV2 have the same design, so it is for example possible to replace the protector PH for the protector PHV1. While developing mounting kits for these protectors our goal is to avoid modifying any original parts when you install them on your motorcycle. Nevertheless in some cases there is no other option and it is for example necessary to adjust the plastic part of motorcycle. If there is a possibility to manufacture a mounting kit which will be attached to multiple points, we will do so because this eliminates a possible damage in the mounting spot during a crash. Mounting kits are made of aluminium alloy and then anodized in black, the adapters are milled on CNC machines.
picture


Crash slider DIAMOND

 

Type SLD

New on the market for the 2014 season. Sliders Diamond are made from POM-C material. They are worked on the 5-axis CNC machines. They are adjusted to the motorcycle by using duralumin adapters. Protector can be rotated according to the shape of the motorcycle.
picture